CNC & Laser Machine Spare Parts
Professional Machines Equipment Manufacture
HyperTherm Shield Plasma (45A – 65A – 85A – 105A – 125A)
The shield is the outermost front consumable on a Hypertherm plasma torch. It fits over the nozzle, protecting it from molten metal that splashes back,…
View Details
P80 Nozzle Plasma Copper
The P80 copper nozzle is a core consumable for the widely used P80 torch found on many air plasma cutters. It sits around the electrode, and its small orifice…
View Details
HQD spindle 4.5 HP (3.5 KW)
This HQD spindle, rated at 3.5 kW (4.5 HP), is the heart of a CNC router: the high-speed motor that holds the cutter and sets how hard the machine can drill,…
View Details
HSD Spindle 4 HP (3 KW)
The spindle is the motor that grips the cutting tool and spins it at high speed on a CNC router. This HSD unit is rated at 3 kW (4 HP) and runs from an…
View Details
Power supply 15V 5A
This is a switching power supply that converts AC mains into a regulated 15V DC output, rated for up to 5A. In laser and CNC machines, units like this feed…
View Details
Cable drag chain – 1 Meter
A cable drag chain is a flexible carrier made of linked segments that guides the moving cables and hoses of CNC routers, laser machines and plasma tables, from…
View Details
Limit switch
The limit switch gives each axis of a CNC router or laser machine a fixed reference point. At start-up the axis travels until it trips the switch, letting the…
View Details
Limit switch
A limit switch is a small sensor mounted at the axis ends of CNC routers, laser cutters and plasma tables. It sends a signal to the controller when the gantry…
View Details
Spindle End Plug Connectors
A spindle end plug is the connector that joins the power cable from the inverter (VFD) to the terminals of a CNC router spindle motor. It is typically a round,…
View Details
RichAuto hand Cable 50 pin
This 50-pin cable connects the RichAuto A11 handheld controller to its interface board on a CNC router. Every command from the handle, from jogging an axis to…
View Details
Gantry cover
The gantry accordion cover is a folding bellows that shields the linear rails, ball screws or racks of a machine from dust, chips and debris. On CNC routers…
View Details
RichAuto Hand keyboard A11
This is the keypad for the RichAuto A11 handheld controller used on CNC routers: the button panel the operator presses to jog axes, set the origin, start,…
View Details
Spendle Wrench AR-25
The AR-25 spindle wrench is a hand tool for tightening and loosening the collet nut on a CNC router spindle. The AR-25 marking indicates the collet nut size it…
View Details
Contactor switch
A contactor is an electrically operated switch that lets a low-power control signal turn heavy loads on and off. In CNC and laser machines it typically…
View Details
Stepper motor 8 N
This stepper motor carries an 8 N rating, the trade shorthand for a holding torque of 8 N·m. A stepper turns through a fixed angle each time its driver sends a…
View Details
Servo motor 750 w
A 750 W servo motor drives a machine axis under closed-loop control: an encoder on the back of the motor continuously reports its position to the servo drive,…
View Details
RichAuto Control system A11
This is the complete RichAuto A11 control package for CNC routers: the handheld controller, the interface board that connects to the drivers and machine…
View Details
RichAuto Hand control A11
The RichAuto A11 hand control is the handheld unit of the A11 DSP control system, widely fitted to CNC routers. It holds the screen and keypad the operator…
View Details
YakoTec. Driver MS-L3
The YakoTec MS-L3 is a motor driver: the electronic module that sits between the machine's controller and an axis motor. It receives low-power pulse and…
View Details
Linear guideway carriage HG-25
The HG-25 linear guideway carriage carries the moving axes of CNC routers and laser cutters along a size 25 rail. Steel balls circulate in closed tracks inside…
View Details
Linear guideway carriage HG-20
The HG-20 carriage, also called a linear block, is the sliding part of a linear guideway system on CNC routers and laser machines. It rides on a hardened rail…
View Details
Ball screw
A ball screw converts the rotation of a motor into precise straight-line movement. Steel balls recirculate between the threaded shaft and the nut, keeping…
View Details
RichAuto Motherboard A11
The RichAuto A11 motherboard is the interface board of the A11 DSP control system used on many CNC routers. It receives commands from the handheld controller…
View DetailsHyperTherm Shield (130A – 200A) MaxPro
This shield is the outermost consumable on a Hypertherm MaxPro plasma torch, made for cutting in the 130A to 200A range. It sits in front of the nozzle, guides…
View Details
HyperTherm Retaining cap
The retaining cap screws onto the front of a Hypertherm torch and holds the consumable stack, meaning the electrode, swirl ring and nozzle, firmly in place. It…
View Details
Nozzle YK-200H (1.3mm – 1.6mm – 1.8mm – 2.2mm)
Designed for the YK-200 plasma torch, this nozzle is available in four orifice sizes: 1.3 mm, 1.6 mm, 1.8 mm and 2.2 mm. The wider spread, reaching 2.2 mm,…
View Details
Nozzle YK-100H (1.2mm – 1.6mm – 1.8mm)
This is the nozzle for the YK-100 series plasma torch, offered with 1.2 mm, 1.6 mm and 1.8 mm orifice diameters. The nozzle focuses the arc into a narrow…
View Details
Swirl ring HyperTherm
The swirl ring sits between the electrode and the nozzle inside a Hypertherm torch. Small angled holes in its wall force the incoming gas to spin around the…
View Details
STARFIRE Control Plasma SF2310-S
The STARFIRE SF2310-S is a CNC control system for cutting machines, used on plasma tables to run the cutting program. It reads the part file, coordinates the…
View Details
Autonics PRL08-1.5DN sensor
The Autonics PRL08-1.5DN is a cylindrical inductive proximity sensor. Following Autonics model coding, it has an M8 threaded body, a 1.5 mm sensing distance…
View Details
YK-100 Plasma CNC Torch
The YK-100 is a machine plasma torch built for automated cutting on CNC tables. Mounted in the torch holder on the Z axis, it delivers the plasma arc that cuts…
View Details
P80 BlackWolf Torch
This is a P80-type plasma cutting torch sold under the BlackWolf name. The torch is the working end of an air plasma system: it receives current and compressed…
View Details
HyperTherm Electrode
This electrode is a consumable for Hypertherm plasma torches. It sits at the centre of the consumable stack, receives the cutting current and anchors the arc…
View DetailsYK-200 Plasma CNC Torch
The YK-200 is a machine-mounted plasma torch intended for CNC cutting tables rather than hand use. It holds the electrode, swirl ring, nozzle and cap in…
View Details
P80 Nozzle Plasma Nickel
The nozzle, sometimes called the tip, is the front consumable of a P80 plasma torch. Its small central orifice squeezes the plasma arc into a narrow,…
View DetailsP80 Electrode Plasma (Copper – Nickel)
The electrode is the part inside a P80 plasma torch where the arc starts and stays anchored during cutting. This version has a copper body with nickel plating.…
View Details
HQD spindle 6 HP (4.5 KW)
HQD spindles are commonly fitted to CNC routers used for furniture parts, signage, decorative panels and plastics. This 6 HP model, equal to 4.5 kW, drives the…
View Details
HSD Spindle 6 HP (4.5 KW)
The HSD spindle is the cutting motor of a CNC router: it holds the tool and spins it at high speed to machine wood, MDF, acrylic, plastics and soft metals.…
View Details
power supply 15 V 10 A
This is a switching power supply with a 15 V DC output rated at up to 10 A, roughly 150 W in total. In CNC routers, laser cutters and plasma tables, units like…
View Details
Spindle 2.2 KW water cooling
This 2.2 kW water-cooled spindle is the cutting motor of a CNC router. Driven by an inverter (VFD) that controls its speed, it turns the cutting tool at high…
View Details
YakoTec. easy servo motor 8 N
The YakoTec easy servo motor 8 N is a closed-loop motor used to drive the axes of CNC routers and similar machines. It combines a stepper motor with an encoder…
View Details
S&A Industrial Chiller CW-5000
The S&A CW-5000 is an industrial water chiller used mainly to cool CO2 laser tubes, and it can also serve water-cooled spindles. Unlike simple radiator-type…
View Details
Silicon tube 1 Meter
This one-meter silicone tube is the water hose that carries coolant between the chiller and the part it cools, most often the glass CO2 laser tube, though it…
View Details
Terminal wire connectors
Terminal wire connectors, known in Egyptian workshops as rozetta, are the terminal blocks used to join and distribute wires inside the electrical cabinet of…
View Details
Laser metal parts set transmission laser
This laser mechanical parts set brings together the metal components of the beam transmission system in a CO2 laser machine. Sets of this kind typically…
View Details.png&w=3840&q=75)
American focus lens
The American focus lens is a US-made CO2 laser optic that sits inside the laser head and converges the beam into a fine focal point. Its quality directly…
View Details
Singaporean focus lens
This Singaporean focus lens is the final optic in the beam path of a CO2 laser machine. Mounted in the laser head, it concentrates the beam arriving from the…
View Details
RD system 6442
The RD 6442 is a Ruida control system for CO2 laser cutting and engraving machines. As the main control unit, it receives jobs from the computer, drives the…
View Details
Silicone laser mirror
This silicon laser mirror, often listed as silicone, is a reflector made on a silicon substrate with a reflective coating, used to direct the CO2 laser beam…
View Details
Metal laser mirror
The metal laser mirror is a reflective optic built on a metal substrate, used in CO2 laser machines to steer the beam from the tube across the gantry to the…
View Details
Laser Tube Plastic Holder
The plastic tube holder is the cradle that supports the glass CO2 laser tube in the rear compartment of a laser cutting and engraving machine. Fitted in pairs,…
View Details
Transformer 70 V
This 70 V transformer converts the mains supply into a lower 70-volt output for the electronics of a CNC or laser machine. In machines of this kind, a…
View Details
Collet – 20
This 20-series collet is the precision sleeve that centers and locks the router bit in the spindle of a CNC machine. Its slotted, tapered body compresses…
View Details
Collet – 25
The Collet – 25 is the slotted clamping sleeve that grips the cutting bit inside the spindle of a CNC router. As the collet nut is tightened, the tapered…
View Details
Automatic Master Switch (overload)
The automatic master switch is the main circuit breaker of the machine. It feeds the entire control cabinet and trips by itself on an overload or short…
View Details
Switch
A disconnect switch isolates the machine, or one of its circuits, from the power supply. On laser, CNC router and plasma machines it usually sits on the…
View Details
Timing belt 550 M
A timing belt is a toothed belt that transmits motion without slipping, keeping the motor and the driven pulley exactly in step. In laser and CNC machines such…
View Details
Schneider AC servo motor 750 W
This is a 750 W AC servo motor from Schneider, used to drive the axes of CNC machines where precise positioning and strong torque across the speed range are…
View Details
Spindle Dust Brush For CNC router
The spindle dust brush is a ring of bristles that hangs around the spindle of a CNC router as part of the dust hood. It forms a flexible curtain between the…
View Details
Collet – 32
A collet is the slotted sleeve that grips the cutting tool inside the spindle of a CNC router. As the spindle nut is tightened, the tapered collet closes…
View Details
Electrical lubricator oiler 220 v for router & plasma machines
This electric lubricator runs on 220V and turns oiling on CNC router and plasma machines into an automatic routine. A built-in motor pump draws oil from the…
View Details
Manual lubricator oiler for router & plasma machines
A manual lubricator is a small lever-operated pump with an oil reservoir that feeds lubricant through thin tubes to the linear guide blocks, ball screws and…
View Details
Power supply 120W
This 120W power supply belongs to the CO2 laser family: it generates the high voltage that drives a laser tube of matching rating. It takes an enable signal…
View Details
Power supply 150W
In CO2 laser machines, a power supply rated in watts like this one is the high-voltage unit that fires the laser tube. It raises mains voltage high enough to…
View Details
Power supply DC 24V 2A
A 24V DC power supply converts mains AC into a steady low-voltage output for the control side of a machine. At 2A it delivers up to about 48 watts, which suits…
View Details
Power socket with fuse
This is the panel-mounted power inlet where the machine's mains cable plugs in, combined with a fuse holder in the same housing. Common on CO2 laser machines…
View Details
CO2 Laser Machine Blade Table
A blade table, also called a knife or slat table, replaces the honeycomb bed of a CO2 laser machine with a row of thin upright metal strips. The material rests…
View Details
CO2 Laser Machine Honeycomb Table
The honeycomb table is the work bed of a CO2 laser machine: a grid of thin metal cells that supports the material while leaving most of the area beneath it…
View Details
Gear
A gear transfers rotation from a motor to a moving part of the machine, changing speed and torque through its tooth ratio. On CNC routers and plasma tables the…
View Details
Cable Drag Chain – 110 cm
A cable drag chain is a flexible track of linked segments that carries and guides cables and hoses along a moving axis. On CNC routers, laser and plasma…
View Details
Limit switch
A limit switch tells the controller that a moving axis has reached a defined point. On CNC routers, laser cutters and plasma tables, limit switches are used…
View Details
Water flow switch sensor
A water flow switch is a safety sensor in the cooling circuit of a laser machine. It detects whether coolant is moving through the line and signals the…
View Details
Driver 783
Driver 783 is a motor driver of the kind used on the motion axes of CNC routers and laser machines. It sits between the motion controller and the axis motor,…
View Details
LeadShine Driver 3DM580
The Leadshine 3DM580 is a digital driver for three-phase stepper motors, used to run the axes of CNC routers and laser machines. It turns the step and…
View Details
Relay
A relay is an electrically operated switch. In CNC routers and laser machines the controller sends a small signal to the relay coil, and the relay's contacts…
View Details
Lens tube
The lens tube is the barrel at the bottom of a CO2 laser cutting head. It houses the focus lens, positions it at the right height above the workpiece, and…
View Details
Lens tube ( liquid cooling )
This lens tube is the part of a CO2 laser cutting head that holds the focus lens at its working distance above the material, built with a liquid-cooling jacket…
View Details
Open-ending Timing Belt – 1 meter
An open-ending timing belt is a toothed drive belt supplied as a straight length rather than a closed loop, sold here by the metre. On laser and CNC machines…
View Details
Suction 550 w
The 550 W suction unit is a fume exhaust fan for laser engraving and cutting machines, drawing smoke away from the bed through the machine's extraction duct.…
View Details
Suction 750 w
This 750 W fume extractor is the exhaust fan that pulls smoke, vapour and fine particles out of the work area of a laser machine. Clearing fumes quickly keeps…
View Details
Linear guideway carriage ( Digital Laser )
This is a linear guideway carriage, the sliding block that runs on a hardened rail and carries the moving parts of the machine, listed here for Digital Laser…
View Details
Power EMI Filter 220 V
A power EMI filter sits at the mains input of a machine and suppresses electrical noise travelling in either direction on the supply line. In laser and CNC…
View DetailsLaser Tube Metal Holder
This metal holder is the bracket that supports the glass laser tube inside a CO2 laser machine. Tubes normally rest on two or more holders that keep them…
View Details
Mirror mount
A mirror mount holds one of the reflective mirrors that steer the beam of a CO2 laser machine from the tube to the cutting head. It keeps the mirror at a set…
View Details
Chiller sensor wire
The chiller sensor wire links the water chiller to the laser machine's control circuit. It carries the chiller's protection signal, so if coolant flow stops or…
View Details
HighTention Cable – 1 Meter
This one-metre high-tension cable carries the high voltage from a CO2 laser power supply to the anode of the laser tube. Its thick insulation is designed to…
View Details
Small Coupling
The small coupling is a compact flexible connector between a motor shaft and a lead screw or ball screw, used where shafts are thinner, such as on lighter axes…
View Details
Large Coupling
A shaft coupling joins the shaft of a stepper or servo motor to the ball screw or lead screw it drives, transferring rotation while absorbing small…
View Details
Signal Lamp
A signal lamp is the indicator light on a machine's control panel or electrical cabinet that shows its status at a glance, for instance whether power is on,…
View Details
Motor 6 lines with Gear
This is a six-wire motor fitted with a gear on its output shaft. Six-lead motors of this kind are typically stepper motors, used in machine motion systems…
View Details
Air valve
An air valve opens, closes or throttles a line of compressed air. On laser and CNC machines it is commonly found in the air-assist supply to the cutting head,…
View Details
Large Coolling Fan
This large cooling fan moves air through the enclosures of CNC and laser machines, where power supplies, drivers and other electronics produce heat during long…
View Details
Hydraulic rod pneumatic
This gas-filled support rod is the strut that helps lift a machine's top cover and hold it open. On laser machines with a hinged lid, it takes much of the…
View Details
Internal Socket 220 V
This 220V internal socket is a power outlet mounted inside the machine's electrical compartment. It gives auxiliary equipment such as the air-assist pump,…
View Details
Water pump for chiller
This water pump is the circulating pump of an industrial chiller, the cooling unit that serves laser machines. It moves coolant from the chiller's tank through…
View Details
side Hinge
A side hinge connects a movable panel to the frame of a machine body, letting a door or access cover swing open while staying attached. On laser and CNC…
View Details
Air compressor 135 w
Rated at 135W, this air compressor supplies the air-assist flow for CO2 laser machines. Air leaving the nozzle clears fumes from the work area, cools the…
View Details
Air compressor 160 w
This 160W air compressor is the air-assist pump used on CO2 laser cutting and engraving machines. It pushes a continuous stream of air through the laser head…
View Details
HighTention flyback transformer 100W
This 100W high-tension flyback transformer sits inside the power supply of a CO2 laser machine. Its job is to step the supply's internal voltage up to the very…
View Details
Laser head set
A complete laser head set is the assembly at the end of the beam path that focuses the laser onto the material. It typically combines the head housing, the…
View Details
Power supply 80W
This 80 W power supply is the high-voltage type typically used to drive CO2 laser tubes of the same power class. It raises the mains voltage to the level…
View Details
Power supply 36 V 10 A
This 36 V 10 A switching power supply converts AC mains into a regulated 36 V DC output with up to 10 A available, or 360 W in total. In CNC routers and laser…
View Details
Ammeter
This ammeter, or current indicator, is usually fitted to the control panel of CO2 laser machines and wired into the laser tube circuit to show the current…
View Details
SPT Tube
SPT tubes are glass CO2 laser tubes that act as the beam source in CO2 engraving and cutting machines used on wood, acrylic, leather, fabric and other…
View Details
SP Tube
The SP tube is a sealed glass CO2 laser tube, the part that actually generates the beam in a CO2 engraving and cutting machine. A high-voltage supply excites…
View Details
S&A Industrial Chiller CW-5200
The S&A CW-5200 is a refrigeration-type industrial water chiller widely used to cool CO2 laser tubes. It circulates water through the tube's cooling jacket and…
View Details
Leadshine High Performance 2-Phase NEMA 23 Hybrid Stepper Motor
This Leadshine high-performance 2-phase hybrid stepper motor in the NEMA 23 frame size drives the axes of CNC routers and laser machines in precise steps…
View Details
Nozzle
The laser nozzle is the small tip fitted to the bottom of a laser cutting head, where the focused beam and the assist gas exit together. Its bore shapes the…
View Details
HyperTherm plasma power source
A Hypertherm plasma power source generates and regulates the cutting current in a plasma system, supplying the torch with power and compressed air through its…
View Details
HyberTherm plasma nozzle
This Hypertherm plasma nozzle is a torch consumable that constricts the plasma arc as it leaves the torch. Its small copper orifice focuses the arc into a…
View Details
StarFire control 2300S
The StarFire 2300S is a numerical control system that runs CNC plasma cutting machines. Acting as the machine's brain, it interprets cutting files, sends…
View Details
Star Fire Plasma Controller 2100C
The StarFire 2100C is a CNC controller for plasma cutting machines. It reads the cutting program, coordinates the axis drives so the torch follows the part…
View Details
THC StarFire SF-HC30A3
The StarFire SF-HC30A3 is a torch height controller (THC) for CNC plasma cutting tables. During a cut it monitors the arc voltage, which rises and falls with…
View Details
LGK Power Source Inverter Air Plasma
The LGK inverter air plasma power source converts mains electricity into the steady direct current a plasma torch needs to cut metal. Using compressed air as…
View Details